Temperature conversion is a formula, not a multiplier
Every other everyday conversion multiplies by a constant. Temperature does not, because Celsius and Fahrenheit place their zero points in different places. The correct approach is a conversion to Celsius, then out to the target scale — and the two traps are applying an offset to a difference, and treating a scale with an arbitrary zero as if it had a real one.
The four formulas
There are only four relationships to remember, and three of them are rearrangements of the others.
- °F = °C × 9/5 + 32
- °C = (°F − 32) × 5/9
- K = °C + 273.15
- °R = °F + 459.67, which is the same as °C × 9/5 + 491.67
Worked: 37 °C is 37 × 1.8 + 32 = 98.6 °F. Body temperature in Fahrenheit is therefore 98.6, and 38 °C is 100.4 °F — the two numbers a clinical thermometer is checked against. Going the other way, 165 °F is (165 − 32) × 5/9 = 73.9 °C, which is why US poultry guidance of 165 °F corresponds to 74 °C elsewhere.
Why multiplication alone fails, in one line
Multiply 20 °C by 1.8 and you get 36, but the answer is 68 °F. The missing 32 is the offset between the two zero points, and it is constant across the entire scale. Convert 0 °C the same way and you get 0 °F, which is wrong by 32 degrees; convert −40 °C and you get −72 °F, wrong by the same 32 degrees but in the other direction.
This is also why the two scales cross at exactly one temperature. Setting F = C in the formula gives C = 1.8C + 32, so −0.8C = 32 and C = −40. Below −40, Fahrenheit numbers are larger than Celsius numbers; above it, Celsius numbers are larger. Any rule of thumb that ignores the crossing point will contradict itself somewhere in the range.
Ratios only work on absolute scales
Kelvin and Rankine start at absolute zero, where molecular motion reaches its minimum. That makes them ratio scales: 600 K is genuinely twice as much thermal energy as 300 K, and doubling a kelvin value is a meaningful operation. Celsius and Fahrenheit start wherever a scientist found convenient in the eighteenth century, so a ratio between two Celsius readings is meaningless — 40 °C is not twice as hot as 20 °C in any physical sense.
Engineering and science use the absolute scales for exactly this reason. A specification written in °R is a specification in Fahrenheit-sized degrees above absolute zero; 500 °R is 277.6 K, or 4.4 °C. If you convert between the two absolute scales, the factor is the same 9/5 that separates the relative ones, with no offset, because both zeros coincide.
A difference is not a reading
This is the trap that catches people who already know the formula. A temperature difference has no zero point to shift, so only the ratio applies: a rise of 10 °C is a rise of 18 °F, not 50 °F. In HVAC work, a supply-air to return-air difference of 10 °C is an 18 °F difference, and adding 32 to it would produce a number that means nothing.
In practice: for readings, use the offset; for differences, use only the factor. If a document gives you two dated readings and asks for the change, convert both readings and subtract — that is the safe order, and it never produces a contradictory result. If it gives you a change directly, multiply by 1.8 (C to F) or 0.5556 (F to C) and add nothing.
Where the extra digits matter and where they do not
A clinical thermometer reads to 0.1 °C, which is 0.18 °F — so quoting a fever as 100.400 °F instead of 100.4 °F adds precision that the instrument never had. An oven dial is worse: a setting of 180 °C typically swings by ±10 °C, so 356 °F is a false precision on a real appliance.
Cold chain and food safety are the places where a single degree matters. Refrigerated transport is specified as 2 to 8 °C, which is 35.6 to 46.4 °F; a logger that reports 45 °F is inside the range and one that reports 47 °F is not. Converting those limits by hand and rounding to whole degrees can move the acceptance boundary by half a degree, which is enough to reject a shipment that was actually fine.
The three historical scales
Réaumur divided the range between freezing and boiling water into 80 degrees, which suited the alcohol thermometers of the 1730s. Newton used 33 steps over the same range, with zero at freezing water. Delisle built his scale downwards from boiling, so 0 °De is 100 °C and 150 °De is 0 °C. None is used for new work, but all three appear in historical documents, old recipes and instrument catalogues. The converter includes them so an archival reading can be translated without guesswork.
Frequently asked questions
Is 0 °C exactly 32 °F?
Yes, by definition. The offset in the Fahrenheit conversion is exactly 32, and the size of a Fahrenheit degree is defined as 5/9 of a kelvin, so 0 °C converts to 32 °F with no rounding error at all.
Should I convert temperature differences with this tool?
No. This converter treats every input as a reading on a scale, which is what a thermometer shows. For a difference, multiply by 1.8 to move from Celsius-sized degrees to Fahrenheit-sized degrees, and do not add 32 or 273.15.
Why do scientists use kelvin instead of Celsius?
Because kelvin starts at absolute zero, which makes it a ratio scale. That matters in any calculation where temperature is multiplied or divided — gas laws, radiation, heat transfer — since those formulas assume zero means no thermal energy.
The temperature converter handles all seven scales with the formulas above, including the historical ones.
Related guides
- Metric vs imperial: the mistakes that cost real money
- Cooking volume conversions that survive real kitchens
Written by the UnitBridge team. Last updated November 19, 2026.