Length converter for metric, imperial and nautical units
Eleven units, one source of truth: the metre. Type a distance on either side and the other side follows immediately — no rounding until the number is displayed.
1 unit in every unit
| Unit | Symbol | Value |
|---|
Other categories: Weight · Temperature · Area · Volume · Speed · Data · Time
Every imperial length is derived from one number
The international yard and pound agreement of 1959 fixed the inch at exactly 25.4 mm. Everything imperial follows from that single figure: twelve inches make a foot, so a foot is exactly 0.3048 m; three feet make a yard at 0.9144 m; 5,280 feet make a statute mile at exactly 1,609.344 m. The nautical mile is separate — it was fixed at 1,852 m in 1929 because one minute of latitude on a great circle is close to that length, which is why aviation and marine distances use it.
On the metric side the chain is even simpler. The metre has been defined since 1983 as the distance light travels in 1/299,792,458 of a second, so centimetres, millimetres, micrometres and nanometres are pure powers of ten away. No conversion between metric units involves a decimal approximation, which is why a metric-only drawing never accumulates rounding error.
| Unit | 1 unit equals | Note |
|---|---|---|
| meter m | 1 m | |
| kilometer km | 1,000 m | |
| centimeter cm | 0.01 m | |
| millimeter mm | 0.001 m | |
| micrometer µm | 0.000001 m | also called a micron |
| nanometer nm | 1e-9 m | |
| inch in | 0.0254 m | exactly 25.4 mm |
| foot ft | 0.3048 m | exactly 0.3048 m |
| yard yd | 0.9144 m | |
| mile mi | 1,609.344 m | statute mile, 5,280 ft |
| nautical mile nmi | 1,852 m | one minute of latitude |
The conversions people actually look up
Most traffic in this category comes from a handful of pairs: metres to feet, kilometres to miles, inches to centimetres. The table below shows them computed from the definitions above, so you can check the tool against a known value.
| Conversion | Result (6 digits) | At 10 digits |
|---|---|---|
| 1 meter → feet | 3.28084 ft | 3.280839895 |
| 1 foot → meters | 0.3048 m | |
| 1 kilometer → miles | 0.621371 mi | 0.6213711922 |
| 1 mile → kilometers | 1.60934 km | 1.609344 |
| 1 inch → centimeters | 2.54 cm | |
| 1 centimeter → inches | 0.393701 in | 0.3937007874 |
| 6 feet → meters | 1.8288 m | |
| 1 nautical mile → kilometers | 1.852 km | |
| 1 yard → meters | 0.9144 m | |
| 1 meter → inches | 39.3701 in | 39.37007874 |
Where length conversions go wrong
- Rounding twice. If you convert metres to feet, round to two decimals, then convert back, you do not get the original number. Convert at full precision and round once, at the end.
- The US survey foot. Surveyors used a slightly longer foot of 1200/3937 m (0.3048006096 m) for most of the twentieth century. It was retired for federal mapping at the end of 2022, but old property descriptions still reference it, and the difference of about 2 parts per million becomes metres over a kilometre.
- Nautical against statute miles. A nautical mile is 1,852 m, a statute mile 1,609.344 m — a 15 % difference. Flight plans and marine charts use nautical miles; road signs never do.
- Fractional inches. A value like 3/8 in is 9.525 mm, not 9.5 mm. Measuring tapes are graded in halves, quarters, eighths and sixteenths, so a metric conversion of a fractional inch usually needs one extra decimal place.
- Millimetres against centimetres. Construction drawings in the US and UK work in millimetres; drawings in France, Germany and much of Asia work in centimetres. Both are metric, and mixing the two is a factor-of-ten error that is easy to miss on a plan.
Metric prefixes that matter in practice
Millimetres and centimetres are everyday units, but the micrometre (1 µm = 0.001 mm) and nanometre (1 nm = 0.001 µm) matter in manufacturing, optics and semiconductor work. The converter switches to exponent notation below 0.000001, so a nanometre expressed in miles reads as a small negative exponent rather than a string of zeros.
Frequently asked questions
How many feet are in a meter?
One metre is 3.280839895 feet. That is the exact value from the 1959 definition, and six-digit display rounds it to 3.28084 ft. Twelve times that number is 39.37007874 in, which matches the inch conversion in the table.
Is a nautical mile the same as a mile?
No. A statute mile is 1,609.344 m and a nautical mile is 1,852 m, so one nautical mile is about 1.1508 statute miles. Nautical miles are used because one minute of latitude is roughly one nautical mile, which makes chart arithmetic straightforward.
Why do metres to feet and metres to inches show different amounts of precision?
Both results come from the same exact definition. 1 m is 3.280839895 ft and 39.37007874 in; six significant digits gives 3.28084 ft and 39.3701 in. The apparent mismatch is only the display cutting each number at a different decimal place.
Related guides
- Metric vs imperial: the mistakes that cost real money — ounces against fluid ounces, short against long tons, and the rounding habits that hide errors
- Unit conversion for cross-border shopping and shipping — how product dimensions and weights decide what you pay
Written by the https://example.com team. Last updated November 19, 2026.